diff --git a/docs/guides/vpn/wireguard/internal.md b/docs/guides/vpn/wireguard/internal.md
index 42250d5..1c2f91a 100644
--- a/docs/guides/vpn/wireguard/internal.md
+++ b/docs/guides/vpn/wireguard/internal.md
@@ -30,8 +30,21 @@ A properly configured firewall is ***highly*** recommended for any Internet-faci
 
 ## Enable NAT on the server
 
+### `nftables` (most distributions)
+
 On your server, add the following to the `[INTERFACE]` section of your `/etc/wireguard/wg0.conf`:
 
+```bash
+PostUp = nft add table ip wireguard; nft add chain ip wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip wireguard wireguard_chain counter packets 0 bytes 0 masquerade; nft add table ip6 wireguard; nft add chain ip6 wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip6 wireguard wireguard_chain counter packets 0 bytes 0 masquerade
+PostDown = nft delete table ip wireguard; nft delete table ip6 wireguard
+```
+
+You may need to install `nftables` using `sudo apt-get install nftables`.
+
+### `iptables` (older distributions)
+
+If you are using a different distribution, you may need to use `iptables` instead of `nftables`. In this case, add the following to the `[INTERFACE]` section of your `/etc/wireguard/wg0.conf`:
+
 ```bash
 PostUp = iptables -w -t nat -A POSTROUTING -o eth0 -j MASQUERADE; ip6tables -w -t nat -A POSTROUTING -o eth0 -j MASQUERADE
 PostDown = iptables -w -t nat -D POSTROUTING -o eth0 -j MASQUERADE; ip6tables -w -t nat -D POSTROUTING -o eth0 -j MASQUERADE
@@ -41,19 +54,9 @@ PostDown = iptables -w -t nat -D POSTROUTING -o eth0 -j MASQUERADE; ip6tables -w
 !!! warning "**Important:** Substitute interface"
     **Without the correct interface name, this will not work!**
 
-    Substitute `eth0` in the preceding lines to match the Internet-facing interface. This may be `enp2s0` or similar on more recent Ubuntu versions (check, e.g., `ip a` for details about your local interfaces).
-<!-- markdownlint-enable code-block-style -->
+    Substitute `eth0` in the preceding lines to match the Internet-facing interface. This may be `enp2s0` or similar on more recent Ubuntu versions. If you are unsure, you can use `ip a` to find the correct interface name. The interface name is the one that is connected to the Internet.
 
-<!-- markdownlint-disable code-block-style -->
-!!! warning "**Important:** Debian Bullseye (Debian 11) and Raspian 11"
-    Debian Bullseye doesn't include iptables per default and uses nftables.
-    (you may need to install `nftables` using `sudo apt-get install nftables`)
-
-    We have to set following rules for PostUP and PostDown:
-    ```bash
-    PostUp = nft add table ip wireguard; nft add chain ip wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip wireguard wireguard_chain oifname "eth0" counter packets 0 bytes 0 masquerade; nft add table ip6 wireguard; nft add chain ip6 wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip6 wireguard wireguard_chain oifname "eth0" counter packets 0 bytes 0 masquerade
-    PostDown = nft delete table ip wireguard; nft delete table ip6 wireguard
-    ```
+    If you are using the `nftables` method, you do not need to specify the interface name in the `PostUp` and `PostDown` lines.
 <!-- markdownlint-enable code-block-style -->
 
 `PostUp` and `PostDown` defines steps to be run after the interface is turned on or off, respectively. In this case, iptables is used to set Linux IP masquerade rules to allow all the clients to share the server’s IPv4 and IPv6 address.
@@ -67,8 +70,8 @@ The rules will then be cleared once the tunnel is down.
     Address = [Wireguard-internal IPs of the server, e.g. 10.100.0.1/24, fd08:4711::1/64]
     ListenPort = 47111
 
-    PostUp   = iptables -A FORWARD -i %i -j ACCEPT; iptables -A FORWARD -o %i -j ACCEPT; iptables -t nat -A POSTROUTING -o enp2s0 -j MASQUERADE
-    PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -D FORWARD -o %i -j ACCEPT; iptables -t nat -D POSTROUTING -o enp2s0 -j MASQUERADE
+    PostUp = nft add table ip wireguard; nft add chain ip wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip wireguard wireguard_chain counter packets 0 bytes 0 masquerade; nft add table ip6 wireguard; nft add chain ip6 wireguard wireguard_chain {type nat hook postrouting priority srcnat\; policy accept\;}; nft add rule ip6 wireguard wireguard_chain counter packets 0 bytes 0 masquerade
+    PostDown = nft delete table ip wireguard; nft delete table ip6 wireguard
 
     # Android phone
     [Peer]
diff --git a/docs/guides/vpn/wireguard/server.md b/docs/guides/vpn/wireguard/server.md
index f60f753..b7f6e87 100644
--- a/docs/guides/vpn/wireguard/server.md
+++ b/docs/guides/vpn/wireguard/server.md
@@ -15,7 +15,7 @@ Installing everything we will need for a `wireguard` connections is as simple as
 sudo apt-get install wireguard wireguard-tools
 ```
 
-For Ubuntu 18.04 and lower, you need to do some extra steps:
+For Ubuntu 18.04 and before, you need to do some extra steps:
 
 ```bash
 sudo add-apt-repository ppa:wireguard/wireguard